PLUMBING ESSENTIALS: A PREREQUISITE FOR INSTALLING A BATHTUB

Plumbing Essentials: A Prerequisite for Installing a Bathtub

Plumbing Essentials: A Prerequisite for Installing a Bathtub

Blog Article

Visit

How do you actually feel in relation to How to Install a Bathtub?


How to Install a Bathtub Yourself
Mounting a bath tub isn't exactly rocket science, however it does require strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately hard project. If the old bathtub is readily obtainable, the task can move rapidly; if you have to open up a wall to get rid of the old bathtub and place the new bath tub, the job is a lot harder. In either instance, the task is within a house handyman's abilities, although you will certainly require a helper to leave the old tub and also set in the new one. Make certain you have actually qualified on your own for the job and also fit attempting it. Rather than employing a contractor to take over a halfway-completed task, it is much better to consider utilizing one prior to you begin. Chances are you may require a specialist plumber to make tube connections.
This short article will help you mount a brand-new tub in your restroom if you have already acquired a brand-new bathtub and also don't require to alter the plan of your previous water system pipelines.
Your devices and also material list need to make up the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you need to change old faucets with new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, turn on the faucets to drain any water remaining in the system. The process of getting rid of the existing taps can be quite bothersome due to the restricted gain access to that is typically the instance.
    Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this process. When the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any old securing substance.
    Prior to going on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.

    Suitable New Taps


    If the tails of the new taps are plastic, then you will require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a link to the existent supply pipelines.
    If you need to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
    Next off, place the tap in the mounting opening in the bath/basin making certain that the washers remain in area between the faucet and also the sink. Protect the faucet in place with the maker offered backnut. As soon as the tap is safely in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap connectors. The previous kind must be attached to the tap finishes initially, tightening only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.

    Installing the Bath tub


    Making use of the two wooden boards under its feet, place the bath tub in the needed setting. The wood boards are useful in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four tiny factors.
    The next goal is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub until the spirit level reviews degree.
    To mount faucets, fit all-time low of the furthest versatile tap connector to the ideal supply pipeline by making a compression join; then do the exact same for the other tap.
    Switch on the supply of water and check all joints and also brand-new pipework for leakages and tighten them if needed. Fill the tub as well as likewise inspect the overflow electrical outlet and the normal electrical outlet for leakages.
    Finally, deal with the bath paneling as described in the producer's user's manual. Tiling as well as securing around the bathtub must wait until the bath tub has actually been made use of at least once as this will resolve it right into its final setting.

    Planning for the Setup


    Firstly, the supporting frame supplied with the bathroom must be fitted (if needed) according to the maker's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to see to it that if the tap features a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to prevent stress on the bathtub.
    Fit the versatile tap adapters to the bottom of both taps using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you make use of every one of the provided washing machines.
    Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its last placement.

    Tiling Around the Bath tub


    In the area where the bath meets the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to break a stiff seal, creating the water to penetrate the wall surface between the bathroom and the tiling, causing difficulties with moisture and also feasible leakages to the ceiling below.
    You can choose from a selection of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and also cartridges, and also can sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked paper or soft rope. Remember to constantly fill up the bathtub with water prior to securing, to enable the motion experienced when the bathtub is in use. The sealer can fracture fairly very early if you do not take into consideration this activity prior to sealing.
    Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally conveniently readily available on the marketplace. It is advisable to fit the tiles making use of waterproof or water-proof glue and cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub

    We were made aware of that article about Installing A Bathtub through someone on a different domain. Enjoyed reading our piece? Please share it. Help somebody else locate it. Thank you so much for your time spent reading it.


    Book A Free Estimate

    Report this page